BUY LED DRIVER
OUR ENGINEERS
REPAIRING
LED Driver Replacement is a difficult process. When an LED fixture fails you need to either purchase a new fixture or replace the driver. In most scenarios it’s the LED driver that needs replacement (LED components have a longer shelf life).
LEDDOMAIN
Lighting
Every LED requires an operating device (ballast). These are called drivers in the linguistic usage. In an LED, current can only flow in one direction (diode). When heated, the current and thus the power consumption in the LED can increase, which leads to further heating. If this is not limited, the LED destroys itself. Preventing this is one of the tasks of the driver.
FOR TRAVELERS
TRIDONIC 87501147 Driver LC 30W 350-700mA DA SC SNC4
SALE PRODUCTS
Driver LC 45W 1050mA fixC SR SNC2 45W 87500771 TRIDONIC
AED0.00
essence series
Product description
- Independent driver with strain-relief housing
- Extra flat housing for constrained installation conditions (small ceiling cut outs and low ceiling voids)
- For luminaires with M and MM as per EN 60598, VDE 0710 and VDE 0711
- Temperature protection as per EN 61347-2-13 C5e
- Output current 1,050 mA
- Nominal lifetime up to 50,000 h
- 5 years guarantee
SR-SB2835RAC-S
AED0.00
* Pricing Available upon Request *
Product Description
With input and output voltage range of 100-240VAC, this RF+Bluetooth rotary smart dimmer can work under no neutral wiring and with neutral wiring. This device supports resistive loads, capacitive loads or inductive loads, and enables to set minimum brightness and startup brightness. For the RF+Bluetooth rotary smart dimmer, both leading edge version and trailing edge versions are available for choosing, and its factory default is trailing edge. Moreover, it can be controlled through both smart App and remote controls, and no gateway is required. By virtue of standard size, this dimmer can be compatible with existing EU standard frames, and installed into standard size wall box. With push switch input, it can be controlled by universal AC push switches.
Constant Voltage DALI Dimmer SR-2304B(WP)
AED0.00
* Pricing Available upon Request *
Product Description
The DALI Dimmer SR-2304B is a constant voltage dimming controller with 4 channel, 5A per channel output, which complies to standard DALI protocol with 1 DALI address to control 4 channels synchronously. The DALI address can be manually assigned and shown on the numeric digital display or automatically assigned by master controllers. 1-4 DALI addresses can be configurable for 4 channels to work synchronously or separately. 0.1%-100% smooth dimming can be achieved by the DALI dimmer via logarithmic dimming, which is perfect for human's vision. The DALI dimmer can not only be compatible with DALI masters, but also push switch to get dim and switch functions under the situation without DALI signal.
60X60-TR-28002342
AED0.00
key Features
Color temperatures 3,000, 4,000 and 6,500 K ⢠Two luminous flux range variants 2,800 or 3,800 lm ⢠Efficacy of the module up to 120 lm/W ⢠High colour rendering index CRI > 80 ⢠Small colour tolerance MacAdam 41 ⢠Small luminous flux tolerances ⢠UGR < 19 Mechanical properties ⢠Module dimension 595 x 595 mm and 620 x 620 mm System solution ⢠LED system solution with outstanding system efficacy up to 101 lm/WSRPC-2309PRO-24-200CVF
* Pricing Available upon Request *
Product Description
With the maximum output power of 200W, this 4-in-1 200W DALI DT8 LED Driver is in compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2, IEC 62386-209:2011. Featured with built-in DALI-2 interface and 4-channel 12VDC/24VDC constant voltage output, this device has a full isolated metal casing. Its PF is greater than 0.98 and its efficiency is greater than 93%. For this LED driver, 4 universal device types: primary N, Tc, XY coordinate and RGBW, can be set by the buttons. Besides, only 1 address is required to control 4 outputs separately under primary N mode. This driver is suitable for indoor LED lighting applications with 5-year warranty.
LEDDOMAIN
ALUMINIUM PROFILE MANUFACTURER
The LED strip light's adhesive backing inside the aluminum channel, snap on the diffuser cover. Rigidly build anodized aluminum material, better heat dissipation, providing great protection for delicate LED strip lights. This kit includes the aluminum led channel, PC Opal diffuser, end caps and mounting clips , pre assembled plug & play connectors . Standard length 1m , 2m , 3m , customization option available as per project requirement .
ABOUT OUR FACTORY
COMPANY HISTORY & FACTS